ENGINE POWER:
At flywheel: 55 HP/DIN
ENGINE:
Fiat 8035.06
4 - Stroke, 3 Cylinders
Direct Injection Diesel,
Max. Power: 2500 rpm 55HP/DIN (41.0 kw)
Max. Torque: 1500 rpm 185NM (18.88 Kgm)
Dry Type Cylinder Liner
Water Cooling
Bore & Stroke: 100 x 115 mm.
Piston Displacement: 2,710 cc.
Compression Ratio: 17:1
Three row brass tube and copper fin radiator
Force-feed lubrication system
Distributor-type injection pump with mechanical speed governor
Four-Bearing Crankshaft
12 Volt Starting System; 4 hp Motor
400 Watt Alternator
90/95 Ah Battery located in front of radiator
Gearbox Mounted Starter Safety Switch
Vertical Exhaust Muffler
OPERATING WEIGHT:
1,710 Kg with 6.00-16 and 12.4/11-28 Tyres, hydraulic lift with three-point linkage cat. 1-2, square type fender with flat top.
TRANSMISSION:
Gearbox with Constant-Mesh Gears
Gears: 8 Forward 2 Reverse Speeds
Synchromesh: 3rd, 4th, 7th, and 8th Speeds
Differential with Pedal Actuated Lock
and Automatic Disconnection.
Single-Reduction Spur Gear Final Drives
STEERING:
Manual, recirculation ball type
Centre relay lever
Joints lubricated for life
DRIVER'S SEAT:
Fully upholstered with parallelogram suspension, adjustable to driver's weight
FRONT AXLE:
Telescopic type, inverted U, variable tread
CLUTCH:
Dual Plate, dry type, with separate controls
(pedal for transmission and hand lever for PTO)
Diameter of plates: 11 in.
POWER TAKE-OFF:
13/8? ? 6 Spline Shaft
Fully Independent: 540 rpm at
2,160 Engine rpm
High-Speed PTO* (13/8? shaft)
Same Speed as Engine.
* Depends on belt pulley
FILTERS:
- Air: oil-bath with precleaner and semiautomatic dust unloader
- Fuel: 2 replaceable cartridges
- Oil: easy-to-change, full-flow cartridge
Vertical exhaust muffler
Gearbox mounted starter safety switch
FUEL TANK:
Capacity: 54 liters
HYDRAULIC LIFT:
With draft and position control
Draft control through top link
Gear - type pump driven from engine crankshaft
Pump capacity: 22.7 lit/min
Relief valve opening pressure: 150-170 kg/sq. cm.
3-point linkage Cat. 1-2
Manual response control
Lower links with sway restrictors and transverse retaining spring
Control lever with safety stop
Max. lifting capacity: 1540 kg |
|
TYRES:
Front: 6.00-16
Rear: 12.4/11-28
LIGHTING SYSTEM:
With 3-position headlights; rear position and number plate lights.
2-pole power connector (ASAE)
Blue high beam warning light on dashboard
BRAKES:
Service: dry, band-type with mechanical control
Parking: with hand lever, on right of operator
THREADS:
Front (8 positions)
1320 - 1420 - 1520 - 1620 - 1720n - 1820 - 1920 - 2020mm
Rear (8 positions)
1200 - 1300 - 1400 - 1500 - 1600 - 1700 - 1800 - 1900mm
DIMENSIONS:
(with 6.00-16 and 12.4/11-28 tyres)
Wheelbase: 1,920mm
Overall Length: 2,960mm
Height to Top of Hood: 1,390mm
Height to Steering Wheel: 1,490mm
Front Tread (8 positions): 1,320 ? 2,020mm
Rear Tread (8 positions): 1,200 ? 1,900mm
Ground Clearance: 480mm under Front Axle
OPTIONAL:
ENGINE
Cold starting aid (Thermostat)
Radiator screen
TRANSMISSION:
Additional creeper speed reduction unit,
for a total of 12 forward and 3 reverse speeds
STEERING:
Hydrostatic Power, with independent circuit
POWER TAKE-OFF
540 rpm (1 3/8" - 6 spline shaft)
Proportional ground speed, revolutions per approx. one metre forward travel (independently of gear engaged): 4.05
TOWING ATTACHMENTS:
Swinging drawbar Cat A
Linkage drawbar Cat A-C
BELT PULLEY:
Diameter: 250mm
Width: 150mm
Pulley speed: 1350 rpm
Belt Speed: 17.7 m/sec
OPTIONAL EQUIPMENT:
- Front End Weights with Frame
- PTO Pulley (MADFI Design)
- DTO Pulley
- MADFI SunRoof Canopy (Fiber Glass/Hard Top)
- 9 Hole Draw Bar
- Pintle/Trolley Hook (MADFI Design)
- DTO Suction Pump
- High Clearance Kit |
